1.General Description
This specification applies to the 5.0 inch color TFT LCD module G050VTN01.0.
G050VTN01.0 is built in timing controller and TTL interface.
The screen format is intended to support the WVGA (800(H) x 480(V)) screen and 16.2M (6bits + FRC)
G050VTN01.0 is a RoHS product.
2.AUO G050VTN01.0 Optical Details
| Items | | Unit | Specifications | |
| | | | | |
| Screen Diagonal | | [inch] | 5.0 | |
| | | | | |
| Active Area | | [mm] | 108.0(W) x 64.8(H) | |
| | | | | |
| Pixels H x V | | | 800 x 3(RGB) x 480 | |
| | | | | |
| Pixel Pitch | | [mm] | 0.135(W) x 0.135(H) | |
| | | | | |
| Pixel Arrangement | | | R.G.B. Vertical Stripe | |
| | | | | |
| Display Mode | | | TN, Normally White | |
| | | | | |
| Nominal Input Voltage VDD | | [Volt] | 3.3 typ. | |
| | | | | |
| LCD Typical Power Consumption | | [Watt] | 0.25 typ. | |
| | | | | |
| Back Light Power Consumption | | [Watt] | 0.54 typ. | |
| | | | | |
| Weight | | [Grams] | 58±2 | |
| | | | | |
| Physical Size | | [mm] | 120.7(W) x 76.3(H)x 3.1(D) | |
| | | | | |
| Electrical Interface | | | 40 pins RGB 8-bits | |
| | | | | |
| Surface Treatment | | | Glare type, 3H | |
| | | | | |
| Support Color | | | 16.2M(6 bits + FRC) | |
| | | | | |
| Temperature Range | | [oC] | | |
| Operating | | -20 to +70 | |
| Storage (Non-Operating) | | [oC] | -30 to +80 | |
| RoHS Compliance | | | RoHS Compliance | |
| | | | | |
| Gray Scale Inversion Direction | | | 6”o’clock | |
| | | | | |
3.Reliability Test Criteria
| | Items | Required Condition | | Note |
| | | | | |
| | Temperature | 60/90%,240 hours, Power On | | |
| | Humidity Bias | | | |
| | High Temperature | 70,240 hours | | |
| | Operation | | | |
| | Low Temperature | -20,240 hours | | |
| | Operation | | | |
| | | | | |
| | Hot Storage | 80,240 hours | | |
| | | | | |
| | Cold Storage | -30,240 hours | | |
| | | | | |
| | Thermal Shock | -30(30mins)<- -> + 80 (30 mins) Total 50 Cycles | | |
| | | | | |
| | Shock Test | 60G,6ms, 3 times for each direction | | |
| | (Non-Operating) | | | |
| | | | | |
| | Vibration Test | Frequency Range : 10 ~ 55 Hz | | |
| | | Stroke : 1.5mm Sweep : 10 Hz ~ 55 Hz ~ 10 Hz | | Note 1 |
| | (Non-Operating) | | | |
| | | | | |
| | | 2 hours for each direction of X, Y, Z(6 hours of total) | | |
| | Vibration Test | Acceleration :2.0G | | |
| | | Frequency Range : 10 ~ 100 Hz | | |
| | (Packaging Box) | | | |
| | | 2 hours for each direction of X, Y, Z.(6 hours of total) | | |
| | On/off test | On/10 sec, Off/10 sec, 30,000 cycles | | |
| | | | | |
| | | | | |
| | | Height: 750mm | | |
| | Drop Test | Drop test must be done 6 times | | |
| | | | | |
| | | Once corner each time | | |
| | | One flat sides each time | | |
| | | Contact Discharge: ± 4KV, 150pF(330Ω ) | | |
| | ESD | Air Discharge: ± 8KV, 150pF(330Ω ) | | Note 1 & 2 |
| | | | | |
| | | 6 times at each test point | | |
4.Safety
4.1 Sharp Edge Requirements
There will be no sharp edges or corners on the display assembly that could cause injury.
4.2 Materials
4.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO toxicologist.
4.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process.
The pRxINted circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be pRxINted on the pRxINted circuit board.
4.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards.
4.4 National Test Lab Requirement
The display module will satisfy all requirements for compliance to:
UL 1950, First Edition U.S.A. Information Technology Equipment
